Garage Door Spring Installation

    Garage door not opening or stuck? Looking for a professional technician?

    Get in touch with our garage door repair team and help is on it’s way! When it comes to garage door service in Indianapolis and its surroundings, Better leave it up to the professionals. For a FREE quote and estimate..

    ☎️ (463) 209-8538

    Or, fill out this form and we will contact you shortly



    Show us the damage: Send us some photos for a FREE cost estimate.

    When it comes to the garage door spring installation, it is imperative that only professionals perform it.

    Given that, we recommend you always reach out to a garage door installation in Indianapolis.

    But, as a guide, here are some of the steps that professionals take for a garage door spring installation:

    Close the garage door first.

    It is important that the garage door is shut first for you to give the spring easy access.

    In order to get ready for this, it should be ensured that the tools for the job are all at hand.

    Check that the garage door opener has also been disconnected for safety reasons.

    Moreover, to ensure safety, keep the door open by means of attaching a c-clamp on the garage door track that is located at the top of the roller.

    This roller can be found at the end of both sides of the overhead door.

    Take out the old springs.

    Get a wrench and then loosen the two sets of screws that are found on the winding cone.

    After that, you have to place the winding bar into the hole that is at the bottom of the cone.

    Make sure that you have a strong grip on the winding bar as well.

    Afterward, you should be able to ascertain the expansion of the spring while the screws loosen.

    In order to have the springs removed, simply unwind them by means of the winding bars.

    Once that has been done, position the winding bar into a new hole, which is positioned on the cone.

    After the springs of the garage door have been unwinded without any more tension, simply utilize a wrench to detach the bolts.

    These bolts connect the spring with the center bracket.

    Then, dislodge the screws that are located on the drums of the cable by means of the wrench.

    After they have been dislodged, remove the nuts and then the bolts and then detach the lift cables as well as the drums from the torsion shaft.

    Proceed to spring installation.

    Check for any parts that have been worn out first before you begin the proper installation.

    An example of this is to make sure the fluid movement of the bearings.

    If these bearings are not moving smoothly, make use of a silicone spray for a lubricant on the garage door.

    If the lubricant does not work, simply purchase new bearing plates in addition to the new springs.

    When installation the springs, begin by installing the left spring.

    After that, place it on the shaft, similar to how the old springs were detached earlier.

    The cable drum should be replaced on the garage door’s other side when the door is in need of two springs.

    Once you have installed the cable drums, proceed on focusing the torsion shaft in the plates.

    After, secure the stationary cones to the plate by making use of the nuts as well as bolts, which you have removed earlier.

    Put a vice-grip on the torsion shaft to make sure that it stays in place.

    Wind the cable then around the drum and then secure it with the set screws.

    Simply leave the vice grip fastened there and then repeat the same step for the cable drum that is located on the right.

    Both sides of the door will require tension that is equal to make sure that the cable drums have been fastened while having the same tension.

    Put tension on the springs by means of the winding bars.

    Also, ensure that you have the right amount of tension and have the set screws properly fastened on the cones once more.

    Call Naptown Garage Doors

    When it comes to the garage door spring installation, you have come to the right place.

    Naptown Garage Doors is the perfect garage door company for you.

    We are a team of professionals who offer garage door repair in Indianapolis as well as garage door installation in Indianapolis.

    We guarantee a service that has been proven and tested by our previous customers.

    Furthermore, we only offer satisfaction and quality services to every customer out there.

    Do not stress about it!

    For a garage door spring installation, contact Naptown Garage Doors.

    Call us now!

    Rate this post
    We hope you enjoyed the above article titled Garage Door Spring Installation. For more great articles such as “Garage Door Spring Installation”, feel free to browse our blog for more great content. Naptown Garage Doors.

    Recommended articles

    garage door rust

    How to Deal with Garage Door Rust

    If you have a garage, then you know that garage door rust can be a huge problem. Over time, the metal on your garage can start to corrode and rust. This can cause the door to become weak and brittle, which could lead to it

    Read More »
    how to open garage door without power

    How to Open a Garage Door Without Power

    If you ever find yourself in a situation where you need to open your garage door but the power is out, don’t worry – there are several ways to do it! In this blog post, we will discuss three different methods that you can use

    Read More »
    Contact Us
    COVID-19 NOTICE:
    Our technicians are equipped with masks and gloves complying with health and safety regulations.
    This is default text for notification bar