Garage Door Torsion Spring Repair

    Garage door not opening or stuck? Looking for a professional technician?

    Get in touch with our garage door repair team and help is on it’s way! When it comes to garage door service in Indianapolis and its surroundings, Better leave it up to the professionals. For a FREE quote and estimate..

    ☎️ (463) 209-8538

    Or, fill out this form and we will contact you shortly



    Show us the damage: Send us some photos for a FREE cost estimate.

    A garage door torsion spring repair should only be done by a professional garage door repair in Indianapolis.

    However, to give you a glimpse of the job, here are some of the steps that should be performed:

    Get ready for the job.

    Before you try to perform the garage door torsion spring repair, you should first make sure to disconnect the garage door opener while the door is shut.

    Simply unplug the opener from the door by means of pulling the release cord.

    Clamp one of the vice-grip pliers into the vertical track that is located above the rollers.

    This is to prevent the garage door from opening when the torsion springs have been installed.

    Begin removing and replacing the springs.

    For the old springs that still have tension, just insert a winding bar to the winding cone.

    After that, utilize a socket wrench to remove the setting or the holding screws slowly.

    This will then have the tension released on the winding bar.

    Then, simply remove the tension and stop when the winding bar is now facing the floor and is pressed on the door.

    Afterward, place the second winding bar to the winding cone, then lift it up to detach the first winding bar.

    After that, simply detach the second winding bar until it has been pointed to the floor.

    Utilize the two winding bars in order to remove the tension, by turning it one-quarter at a time.

    Just remember to be patient and never to place your hand on the springs just to attain stability.

    When you use the winding bars, keep in mind to place them away from the face and the clothes.

    After you have completely unwound the two springs and they now have zero tension, proceed to the removal of the center bolts, which connect the two springs together.

    Then, loosen the cable drums and have the cable released.

    Pull each drum to the middle of the torsion shaft afterward.

    After that has been down, simply file down some screw marks on the shaft.

    Then, pull the shaft out of the rear bracket, then have the cable drum removed, as well as the spring.

    Place the new spring on the torsion shaft and ensure that the red winding cone is placed on the garage’s left side.

    The opposite spring should have a winding cone that is black.

    Simply have these steps repeated about seven and eight on the other side.

    Secure it.

    While you place the torsion shaft into place, just place the springs back at the center.

    Then, reattach the cable to the cable drum at the left, and then run it.

    Fasten the drum onto the shaft afterward.

    Using the cable taut, place a vice-grip to the torsion shaft and have it secured against the header.

    Place the cable to the cable drum at the right, then run it again, and have it fastened onto the shaft.

    As for the springs, insert the winding bar for the left spring into the cone and have it rotate towards the header.

    Place a second winding bar into the cone and then place it against the door.

    Simply remove the other winding bar, and then lift it upward for a turn, about a quarter.

    You should look into the instruction manual for the specific quarter turns that are required.

    The seven-foot doors typically need about 31 quarter turns, while the eight-foot ones need about 34 turns.

    Once you have finished the turns, just leave one winding bar into the cone and permit it to press against the door securely.

    Then, fasten the set screws that are found on the left side of the torsion spring.

    Remember that if you cannot do any of these, reach out to a garage door repair in Indianapolis.

    Call Naptown Garage Doors

    If you need a garage door torsion spring but are having trouble looking for one, you have come to the right place.

    Naptown Garage Doors is the perfect garage door company for you.

    We are a team of professionals who offer garage door repair in Indianapolis as well as garage door installation in Indianapolis.

    We guarantee a service that has been proven and tested by our previous customers.

    Furthermore, we only offer satisfaction and quality services to every customer out there.

    Do not stress about it!

    For a garage door torsion spring repair, contact Naptown Garage Doors.

    Call us now!

    Rate this post
    We hope you enjoyed the above article titled Garage Door Torsion Spring Repair. For more great articles such as “Garage Door Torsion Spring Repair”, feel free to browse our blog for more great content. Naptown Garage Doors.

    Recommended articles

    garage door rust

    How to Deal with Garage Door Rust

    If you have a garage, then you know that garage door rust can be a huge problem. Over time, the metal on your garage can start to corrode and rust. This can cause the door to become weak and brittle, which could lead to it

    Read More »
    how to open garage door without power

    How to Open a Garage Door Without Power

    If you ever find yourself in a situation where you need to open your garage door but the power is out, don’t worry – there are several ways to do it! In this blog post, we will discuss three different methods that you can use

    Read More »
    Contact Us
    COVID-19 NOTICE:
    Our technicians are equipped with masks and gloves complying with health and safety regulations.
    This is default text for notification bar